10G Active Mux (6x4) with Integrated Re-timers for USB 3.1/DisplayPort.
Overview:
ANX7440 is a re-timing mux capable of switching DisplayPort (DP) and USB 3.1 Gen 2 10Gbps signals to support a single USB Type-C™ (USB-C™) port. ANX7440 has built-in re-timers to recover both the USB and DP signals with loss compensation of 23dB for USB and up to 27dB for DP. ANX7440 supports Separate Reference Clock Independent SSC (SRIS) and Bit-Level Retimer (BLR) architectures for a hybrid implementation for Gen 1 and Gen 2. SRIS re-timers eliminate jitter transfer and guarantee Gen 2 operation. Digital muxing (6x4) is supported by ANX7440 to ensure the enhanced signals from the retimers are preserved and outputted over the USB-C connector. ANX7440 integrates the SBU/AUX mux for switching DP AUX signals and reducing overall system BOM cost
The ANX7440 can be adopted by Intel, AMD, Qualcomm, MTK platform designs.
Main Features:
Built-in re-timers
Integrated re-timers for USB 3.1 up to Gen 2 @ 10Gbps
Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) Architectures of USB3.1 Specification (Appendix-E)
Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps. Supports both transparent mode and nontransparent mode (transparent or LTTPR).
Loss compensation to recover up to 23dB channel loss (USB), up to 27dB (DP)
Integrated mux
Integrated (6x4) mux switches USB and DP signals and preserves enhanced signal output over USB-C connector
Mux control input through I2C commands from external I2C master (or, optionally through FLIP/OP_MODE pins)
Integrated SBU/AUX mux for switching DisplayPort AUX +/- signals
Reference clock for re-timers
Utilizes a 24MHz crystal or 1.05V swing singleended clock source
Serial and debug interfaces
I 2C Slave interface, up to 1MHz, for mux and retimer configuration
DCI debug interface support
Industry standard compatibility
USB 3.1 specification, Appendix E
DisplayPort 1.4 specification
USB Type-C r1.2 specification
Intel USB 3.1 Repeater and Active Switch specification
Low-power design
Analog power supply at 1.8V
Dedicated 3.3V power for PULL_1 and PULL_2, DCI interface
Dedicated supply power pin for I/O power at 1.8V
Packages
BGA-56, 4.0mm x 4.5mm, 0.8mm Z-height,0.5mm ball-pitch
QFN-60, 7.0mm x 7.0mm, 0.90mm Z-height, 0.4mm pin-pitch
20G Active Mux (2x2) with Integrated Re-timer and CC Detection for USB 3.2
Overview:
ANX7434 is a USB 3.2 Gen 2 20G active mux with integrated re-timer and CC Detection capable of recovering the USB signals with loss compensation of up to 23dB. ANX7434 specifically supports Gen 2x2 for USB Type-CTM (USB-CTM) applications. ANX7434 supports Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) architectures for a hybrid implementation for Gen 1 and Gen 2. SRIS re-timers eliminate jitter transfer and guarantee Gen 2 operation. Host (source) and device (sink) USB-C data-only applications are fully supported by ANX7434. With the integrated SRIS re-timer function and x2 USB support, ANX7434 ensures the enhanced signals from the re-timers are preserved and outputted over the USB-C connector.
Main Features:
Built-in re-timers
Integrated re-timer for USB 3.2 up to Gen 2 @ 2x10Gbps for a combined 20G data throughput
Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) Architectures of USB 3.2 Specification (Appendix-E)
Supports both host (source) and device (sink) applications in USB-C subsystems
Loss compensation to recover up to 23dB channel loss
TCPC-compliant hardware interface
Supports DFP and UFP USB-C applications
Dedicated control signals for VBUS Source FET
Integrated Reference CLK
Serial and debug interfaces
I2C Slave interface, up to 1MHz, for mux and re-timer configuration
Industry standard compatibility
USB 3.2 specification, Appendix E
USB Type-C r1.2 specification
Intel USB 3.2 Repeater and Active Switch specification
Low-power design
Analog power supply at 1.8V
I/O power supply at 1.8V
Core power supply at 1.2V
Commercial temperature range of 0C to 70C
Applications:
Notebook/Desktop PC
Storage/Server
Package:
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
ANX7432 is a USB3.2 Gen2 20G active retimer capable of recovering the USB signals with loss compensation of up to 23dB. ANX7432 also integrates a mux to enable the following configurations: (Gen 1x2, Gen 2x1 and Gen 2x2) for USB Type-CTM (USB-CTM) applications. ANX7432 supports Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) architectures for a hybrid implementation for Gen 1 and Gen 2. SRIS re-timers eliminate jitter transfer and guarantee Gen 2 operation. Host (source) and device (sink) USB-C data-only applications are fully supported by ANX7432 with built-in intelligent switching. With the intelligent digital switching, ANX7432 ensures the enhanced signals from the re-timers are preserved and outputted over the USB-C connector.
Main Features:
Built-in re-timers
Integrated re-timer for USB 3.2 with two lanes up to Gen2 @ 10Gbps each for a combined 20G throughput
Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) Architectures of USB 3.2 Specification
Supports both host (source) and device (sink) applications in USB-C subsystems
Loss compensation to recover up to 23dB channel loss
Integrated mux
Digital (2x2) mux switches USB signals and preserves enhanced signal output over USB-C connector
Mux control input through I2C commands from external I2C master (or, optionally through FLIP/USB_EN pins)
Integrated Reference CLK
Serial and debug interfaces
I2C Slave interface, up to 1MHz, for mux and re-timer configuration
Industry standard compatibility
USB 3.2 specification
USB Type-C r1.2 specification
Intel USB 3.2 Repeater and Active Switch specification
Low-power design
Analog power supply at 1.8V
I/O power supply at 1.8V
Core power supply at 1.2V
Commercial temperature range of 0C to 70C
Applications:
Notebook/Desktop PC
Storage/Server
Package:
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
QFN-60, 6.4mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
ANX7406 is a USB Type-C™ (USB-C) Port Controller that complies with the latest USB4 Version 1.0, USB Type C R2.0, and USB-PD v3.1 (r1.0) specifications. ANX7406 integrates the logic to manage cable attach and detach, orientation, and role detection. The on-chip microcontroller (OCM) facilitates USB-PD v3.0 messaging for fast charging, USB4, USB3.2, DisplayPort™ (DP) Alternate Mode (Alt Mode), and Thunderbolt3 Alternate Mode. ANX7406 can be configured as a Downstream Facing Port (DFP) or a Dual-Role Port (DRP), making it an ideal solution for various applications such as notebooks, desktops, and 2-in-1 PCs. ANX7406 supports a TCPC-compliant register interface and utilizes its 2 of I2C Slave ports for communication with an upstream embedded controller and PCH.
Main Features:
USB-PD Support: UFP and DFP
Chunking and unchunking
TCPCI compliant
Fast role swap (FRS)
Integrated VCONN switch
VBUS sense with 36V over current and over voltage protection
USB Billboard class (low speed)
Embedded RISC-V core and secure FW update
96KB instruction RAM, 16KB execution RAM
512KB flash for FW storage
AES128 FW encryption with SHA256 signature
FW update through I2C and billboard device
System Interface and IO control
2x I2C slave interfaces; 1x I2C master interface
HPD signal for DP applications
Role select configuration pin
Industry standard compatibility
USB Type-C r2.0 specification
USB Power Delivery v3.1 r1.0 specification
DisplayPort 2.0 specification
DisplayPort Alternate Mode over USB Type-C V2.0 specification
Universal Serial Bus (USB) Type-C Port Controller Interface r2.0 specification
Dead battery detection support
36V overvoltage protection for CC1/CC2, SBU1/SBU2, VBUS
ANX7433 is a USB 3.2 Gen2 10G active mux with integrated re-timer and CC Detection capable of recovering the USB signals with loss compensation of up to 23dB. ANX7433 also integrates a mux (1x2) for USB Type-C™ (USB-C™) applications. ANX7433 supports Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) architectures for a hybrid implementation for Gen 1 and Gen 2. SRIS re-timers eliminate jitter transfer and guarantee Gen 2 operation. Host (source) USB-C data-only applications are fully supported by ANX7433 with built-in intelligent switching. With the intelligent digital switching, ANX7433 ensures the enhanced signals from the re-timers are preserved and outputted over the USB-C connector.
Main Features:
Other Features
Built-in re-timer
Integrated re-timer for USB 3.2 up to Gen2 @ 10Gbps
Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) Architectures of USB 3.2 Specification (Appendix-E)
Loss compensation to recover up to 23dB channel loss
Integrated mux
Digital (1x2) mux switches USB signals and preserves enhanced signal output over USB-C connector
Mux control input through I2C commands from external I2C master
TCPC-compliant hardware interface
Supports DFP USB-C applications
Dedicated control signals for VBUS Source FET
Integrated Reference CLK
Serial and debug interfaces
I2C Slave interface, up to 1MHz, for mux and retimer configuration
Industry standard compatibility
USB 3.2 specification, Appendix E
USB Type-C r1.2 specification
Intel USB 3.2 Repeater and Active Switch specification
Low-power design
Analog power supply at 1.8V
I/O power supply at 1.8V
Core power supply at 1.2V
Package
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
10G Active Mux (4x4) with Integrated Re-timers for U5B3.2/DisplayPortTM
Overview:
ANX7451 is a 4x4 re-timing mux capable of switching DisplayPort (DP) and USB3.2 Gen 2 10Gbps signals to support a single USB Type-C™ (USB-C™) port. ANX7451 has built-in re-timers to recover both the USB and DP signals with loss compensation of 23dB for USB and up to 27dB for DP. ANX7451 supports Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) architectures for a hybrid implementation for Gen 1 and Gen 2. SRIS re-timers eliminate jitter transfer and guarantee Gen 2 high-speed operation. Host (source) and device (sink) applications are fully supported by ANX7451 with built-in intelligent switching. With the intelligent digital switching, ANX7451 ensures the enhanced signals from the retimers are preserved and outputted over the USB-C connector. ANX7451 integrates the local reference clock and SBU/AUX mux for switching DP AUX signals and reducing overall system BOM cost.
Main Features:
Other Features
Built-in re-timers
Integrated re-timers for USB3.2 up to Gen 2 @ 10Gbps
Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) Architectures of USB3.2 Specification (Appendix-E)
Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps. Supports both transparent mode and non-transparent mode (transparent or LTTPR)
Supports both host (source) and device (sink) applications in USB-C subsystems
Loss compensation to recover up to 23dB channel loss (USB), up to 27dB (DP)
Integrated mux
Integrated (4x4) mux switches USB and DP signals and preserves enhanced signal output over USB-C connector
Mux control input through I2C commands from external I2C master (or, optionally through GPIO of FLIP/USB_EN/DP_EN pins)
Integrated SBU/AUX mux for switching DisplayPort AUX +/- signals
Integrated reference clock
Serial and debug interfaces
I2C Slave interface, up to 1MHz, for mux and re-timer configuration
Industry standard compatibility
USB3.2 specification, Appendix E
DisplayPort 1.4a specification
USB Type-C r1.2 specification
Intel USB3.2 Repeater and Active Switch specification
Low-power design
Analog power supply at 1.8V
I/O power supply at 1.8V
Core power supply at 1.2V
Package
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
LGA-34, 3.3mm x 4.8mm, 0.71mm Z-height, 0.35mm pin-pitch
Commercial temperature range of OC to 70C
Applications:
Accessories
Notebook/Desktop PC
Storage/Server
Package:
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
LGA-34, 3.3mm x 4.8mm, 0.71mm Z-height, 0.35mm pin-pitch
10G Active Mux (6x4) with Integrated Re-timers for USB3.2/DisplayPortl.4
Overview:
ANX7443 is a re-timing mux capable of switching DisplayPort (DP) and USB3.2 Gen 2 10Gbps signals to support a single USB Type-CTM (USB-CTM) port. ANX7443 has built-in re-timers to recover both the USB and DP signals with loss compensation of 23dB for USB and up to 27dB for DP. ANX7443 supports Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) architectures for a hybrid implementation for Gen 1 and Gen 2. SRIS re-timer eliminates jitter transfer and guarantee Gen 2 high-speed operation. Host (source) and device (sink) applications are fully supported by ANX7443 with built-in intelligent switching. With the intelligent digital switching, ANX7443 ensures the enhanced signals from the re-timers are preserved and outputted over the USB-C connector. ANX7443 integrates the local reference clock and SBU/AUX mux for switching DP AUX signals and reducing overall system BOM cost.
Main Features:
Other Features
Features
Built-in re-timers
Integrated re-timers for USB3.2 up to Gen 2 @ 10Gbps
Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) Architectures of USB3.2 Specification (Appendix-E)
Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps. Supports both transparent mode and non-transparent mode (transparent or LTTPR)
Supports both host (source) and device (sink) applications in USB-C subsystems
Loss compensation to recover up to 23dB channel loss (USB), up to 27dB (DP)
Integrated mux
Integrated (6x4) mux switches USB and DP signals and preserves enhanced signal output over USB-C connector
Mux control input through I2C commands from external I2C master (or, optionally through GPIO of FLIP/USB_EN/DP_EN pins)
Integrated SBU/AUX mux for switching DisplayPort AUX +/- signals
Integrated reference clock
Serial control interfaces
I2C Slave interface, up to 1MHz, for mux and re-timer configuration
Industry standard compatibility
USB3.2 specification, Appendix E
DisplayPort 1.4a specification
USB Type-C r1.2 specification
Intel USB3.2 Repeater and Active Switch specification
Low-power design
Analog power supply at 1.8V
I/O power supply at 1.8V
Core power supply at 1.2V
Package
QFN-60, 6.4mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
Commercial temperature range of OC to 70C
Applications:
Notebook/Desktop PC
Package:
QFN-60, 6.4mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
10G Active Mux (1x2) with Integrated Re-timer for USB 3.2
Overview:
ANX7431 is a USB3.2 Gen2 10G active mux with integrated re-timer capable of recovering the USB signals with loss compensation of up to 23dB. ANX7431 also integrates a mux (lx2) for USB Type-C™ (USB-C™ ) applications. ANX7431 supports Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) architectures for a hybrid implementation for Gen 1 and Gen 2. SRIS re-timers eliminate jitter transfer and guarantee Gen 2 operation. Host (source) and device (sink) USB-C data-only applications are fully supported by ANX7431 with built-in intelligent switching. With the intelligent digital switching, ANX7431 ensures the enhanced signals from the re-timers are preserved and outputted over the USB-C connector.
Main Features:
Other Features
Features
Built-in re-timer
Integrated re-timer for USB 3.2 up to Gen2 @ 10Gbps
Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) Architectures of USB 3.2 Specification (Appendix-El
Supports both host (source) and device (sink) applications in USB-C subsystems
Loss compensation to recover up to 23dB channel loss
Integrated mux
Digital (1x2) mux switches USB signals and preserves enhanced signal output over USB-C connector
Mux control input through 12C commands from external 12C master (or, optionally through FLIP/USB_EN pins)
Integrated Reference CLK
Serial and debug interfaces
I2C Slave interface, up to 1MHz, for mux and re-timer configuration
Industry standard compatibility
USB 3.2 specification, Appendix E
USB Type-C rl.2 specification
Intel USB 3.2 Repeater and Active Switch specification
Low-power design
Analog power supply at 1.8V 1/0 power supply at 1.8V
Core power supply at 1.2V
Package
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
Commercial temperature range of OC to 70C
Applications:
Accessories
Notebook/Desktop PC
Package:
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
USB Type-C™ Crosspoint Switch with On-chip Microcontroller
Overview:
ANX7437 is an intelligent crosspoint switch that supports switching at data rates of up to 10Gbps. ANX7437 supports highspeed interfaces, such as USB 3.1 (Gen 1 – 5Gbps, Gen 2 – 10Gbps). ANX7437 is designed as a companion IC to various CPUs and Application Processors (APs) to enable notebooks, desktops, and 2-in-1 PCs to use the reversible USB Type-C (USB-C™) connectors. An On-chip Microcontroller (OCM) is available to manage the signal switching, Channel Configuration (CC) detection, USB Power Delivery (USB-PD) charging and Vendor Defined Message (VDM) protocol, and other functions, as defined in the USB Type-C v1.2 and USB Power Delivery v3.0 specifications. ANX7437 can be configured for a Downstream Facing Port (DFP) or Dual-Role Port (DRP) to support a USB-C receptacle.
Main Features:
Other Features
USB 3.1 signal (SSTX and SSRX) with Gen1 (5Gbps) and Gen2 (10Gbps) link speed
Native TCPC-compliant hardware register interface
Supports DFP and DRP modes for Host-only or Dual-Role applications
Integrated VCONN FETs
Built-in 10-bit ADC to monitor VBUS voltage and current
Dedicated control signals for VBUS Source FET, VBUS sink FET, and VBUS auto discharge circuity
Serial and debug interfaces
Slave interface
Direct Connect Interface (DCI) debug support
Industry standard compatibility
USB Type-C r1.2 specification
USB Power Delivery v3.0 r1.0 specification
Universal Serial Bus (USB) Type-C Port Controller Interface r1.0 specification
Low-power design
Single supply at 3.3V
Dedicated supply power pin for flexible I/O power – 1.8V or 3.3V
Ultra-low power consumption (typical 80uW) in standby mode
On-chip Microcontroller (OCM) to implement signal switching and USB-PD messaging
ANX7412 is a USB Type-C™ (USB-C) Port Controller that complies with the latest USB-C (r1.2) and USB-PD v3.0 (r1.0) specifications. ANX7412 integrates the logic to manage cable attach and detach, orientation, and role detection. The onchip microcontroller (OCM) facilitates USB-PD v3.0 messaging for fast charging, DisplayPort™ (DP) Alternate Mode (Alt Mode), and Vendor-Defined Messages (VDMs). ANX7412 integrates the MOSFETs for powering VCONN and the signals required to control external VBUS load switches. ANX7412 can be configured as a Downstream Facing Port (DFP) or a Dual- Role Port (DRP), making it an ideal solution for USB-C receiver ports such as dongles, docks, HDTV, monitors, and projectors. ANX7412 supports a TCPC-compliant register interface and utilizes its I2C Slave port for communication with an upstream embedded controller, CPU, or AP. ANX7412 is powered from a single flexible supply rail at 3.3V and is available in small QFN packages.
Main Features:
Other Features
TCPC-compliant hardware interface
Supports DFP and DRP modes for Host-only or Dual-Role applications
Integrated VCONN FETs
Built-in 10-bit ADC to monitor VBUS voltage and current
Integrated Billboard
Dedicated control signals for VBUS Source FET, VBUS sink FET, and VBUS auto discharge circuity
Serial and debug interfaces
I2C Master/Slave interface
Industry standard compatibility
USB Type-C r1.2 specification
USB Power Delivery v3.0 r1.0 specification
DisplayPort 1.4 specification
DisplayPort Alternate Mode over USB Type-C r1.1 specification
Universal Serial Bus (USB) Type-C Port Controller Interface r1.0 specification
Low-power design
Single supply at 3.3V
Dedicated supply power pin for flexible I/O power — 1.8V or 3.3V
Ultra-low power consumption (typical 77uW) in standby mode
On-chip microcontroller with reprogrammable memory for USB-PD v3.0 engine
64K bytes SRAM for firmware execution
128K bytes Flash for firmware storage
PDFU function for firmware updating
Dead battery detection support
Package
QFN-28, 4mm x 4mm, 0.8mm Z-height, 0.4mm pin-pitch
Applications:
Accessories
Notebook/Desktop PC
Smartphone/Tablet
Package:
QFN-28, 4mm x 4mm, 0.8mm Z-height, 0.4mm pin-pitch
