10G Active Mux (4x4) with Integrated Re-timers for U5B3.2/DisplayPortTM
Overview:
ANX7451 is a 4x4 re-timing mux capable of switching DisplayPort (DP) and USB3.2 Gen 2 10Gbps signals to support a single USB Type-C™ (USB-C™) port. ANX7451 has built-in re-timers to recover both the USB and DP signals with loss compensation of 23dB for USB and up to 27dB for DP. ANX7451 supports Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) architectures for a hybrid implementation for Gen 1 and Gen 2. SRIS re-timers eliminate jitter transfer and guarantee Gen 2 high-speed operation. Host (source) and device (sink) applications are fully supported by ANX7451 with built-in intelligent switching. With the intelligent digital switching, ANX7451 ensures the enhanced signals from the retimers are preserved and outputted over the USB-C connector. ANX7451 integrates the local reference clock and SBU/AUX mux for switching DP AUX signals and reducing overall system BOM cost.
Main Features:
Other Features
Built-in re-timers
Integrated re-timers for USB3.2 up to Gen 2 @ 10Gbps
Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re-timer (BLR) Architectures of USB3.2 Specification (Appendix-E)
Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps. Supports both transparent mode and non-transparent mode (transparent or LTTPR)
Supports both host (source) and device (sink) applications in USB-C subsystems
Loss compensation to recover up to 23dB channel loss (USB), up to 27dB (DP)
Integrated mux
Integrated (4x4) mux switches USB and DP signals and preserves enhanced signal output over USB-C connector
Mux control input through I2C commands from external I2C master (or, optionally through GPIO of FLIP/USB_EN/DP_EN pins)
Integrated SBU/AUX mux for switching DisplayPort AUX +/- signals
Integrated reference clock
Serial and debug interfaces
I2C Slave interface, up to 1MHz, for mux and re-timer configuration
Industry standard compatibility
USB3.2 specification, Appendix E
DisplayPort 1.4a specification
USB Type-C r1.2 specification
Intel USB3.2 Repeater and Active Switch specification
Low-power design
Analog power supply at 1.8V
I/O power supply at 1.8V
Core power supply at 1.2V
Package
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
LGA-34, 3.3mm x 4.8mm, 0.71mm Z-height, 0.35mm pin-pitch
Commercial temperature range of OC to 70C
Applications:
Accessories
Notebook/Desktop PC
Storage/Server
Package:
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
LGA-34, 3.3mm x 4.8mm, 0.71mm Z-height, 0.35mm pin-pitch
ANX7408 is an intelligent crosspoint switch that supports switching at data rates of up to 6.75Gbps. ANX7408 supports high-speed interfaces, such as USB 3.1 (Gen 1 – 5Gbps). ANX7408 is designed as a companion IC to various CPUs and Application Processors (APs) to enable notebook PCs, tablets, and smartphones to use mobile connectors such as the reversible USB Type-C (USB-CTM). An On-chip Microcontroller (OCM) is available to manage the signal switching, Channel Configuration (CC) detection, USB Power Delivery (USB-PD) charging and Vendor Defined Message (VDM) protocol, and other functions as defined in the USB Type-C v1.1 and USB Power Delivery v2.0 specifications. ANX7408 can be configured for a Downstream Facing Port (DFP), Upstream Facing Port (UFP), or Dual-Role Port (DRP) to support a USB-C receptacle
Main Features:
Other key features
High-speed switching up to 6.75Gbps
USB 3.1 signal (SSTX and SSRX) with Gen1 (5Gbps) link speed
On-chip Microcontroller (OCM) to implement signal switching, USB-PD messaging, and related functions
5V-tolerant CC/VCONN signals
Dead battery charging support
I2C slave mode to support external MCU/IC
VBUS control and USB_ID pins to control external Power Management Integrated Circuits (PMICs) or USB charger IC based on the USB-PD configuration
3.3V power supply for analog part (1.0V Core power generated by internal regulator)
1.8V~3.3V power supply for digital IO
Supports the following
USB 3.1 signal switching
USB Power Delivery Specification v2.0 on CC wire
Compliant with the following
USB Type-C Cable and Connector Specification (rev 1.1)
USB Power Delivery Specification v2.0
USB 3.1 Gen 1 electrical specifications
Applications:
Accessories
Notebook/Desktop PC
Smartphone/Tablet
Standards Compliance:
USB 3.1 Gen 1 electrical specifications
USB Power Delivery Specification v2.0 (rev 1.0)
USB Type-C Cable and Connector Specification (rev 1.0)
ANX9833 is a DisplayPort to VGA adapter IC designed to connect a DisplayPort 1.2/1.1 source to a VGA display. With its on-chip MCU and memory, the ANX9833 does not require any external configuration or setup. It automatically directs DisplayPort output from adapters to VGA, effectively working with all types of legacy monitors, projectors, and TVs. ANX9833 provides Gbps bandwidth over two lanes to reach WUXGA (1920x1200) resolutions.
Main Features:
VGA Output
Resolutions up to WUXGA (1920x1200@60Hz, 24bpp)
VGA output meets VESA VSIS v1r2 clock jitter specification
VGA DAC work range up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detection
Getting power from DisplayPort source
EDID and MCCS pass-through support
DisplayPort Input
VESA® compliant DisplayPort 1.2 receiver
Two-lane high-speed differential input with configurable speed: 2.7Gbps or 1.62Gbps, total bandwidth up to 5.4Gbps
Optimized for VGA Adapters
Integrated MCU and EEPROM for added flexibility
Single 3.3V power supply or 3.3V/1.0V power supply supported
5.0V power output for VGA DDC
Low BOM requirements
System Operation
Field upgradable through DP AUX or I2C
MCU can control external components
-10 to +75o operating temperature
Applications:
Accessories
Notebook/Desktop PC
Package:
6x6mm, 48 QFN (0.4mm pitch)
Standards Compliance:
DisplayPort 1.2
Power Requirements:
600mW active power with all regulators active
Standby power: 12mW with 1V low-dropout (LDO) regulator off
While VGA is losing its popularity in notebooks, there continues to be a need for VGA connections with its huge installed base of monitors, projectors, and TVs. The ANX6212, designed for motherboards, addresses this gap through the high performance DisplayPort to VGA converter of its kind. With its on-chip MCU and memory, the ANX6212 does not require any external configuration or setup. The ANX6212 automatically directs the DisplayPort output from the PC or mobile phone to VGA, effectively working with all types of legacy monitors, projectors, and TVs.
Main Features:
VGA Output
Supports resolutions up to WQXGA (2560x1600@60Hz, 24bpp)
VGA output conforms to VESA® VSIS v1r2 clock jitter specification
VGA output pixel rate up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detect
EDID and MCCS pass-through support
DisplayPort Input
VESA compliant DisplayPort 1.2 receiver
VESA compliant eDP v1.3 receiver
Two-lane high-speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Optimized for VGA Adapters
Integrated MCU and EEPROM for added flexibility
Single 3.3V power supply
5.0V power output for VGA DDC
Minimum BOM requirements
System Operation
Under 350mW operation at WUXGA resolutions (no regulators)
Field upgradable through DP AUX or I2C
MCU can control external components
-10 to +75o C operating temperature
Applications:
Automotive
Notebook/Desktop PC
Package:
6x6mm, 48 QFN (0.4mm pitch)
Standards Compliance:
DisplayPort 1.2
eDP 1.3
Power Requirements:
600mW active power with all regulators active
Standby Power: 12mW with 1V low-dropout (LDO) regulator off
The ANX6211 is a DisplayPort to VGA converter featuring low power consumption, high performance, and cost-effective. Designed for motherboards, the ANX6211 is optimized in terms of space, power, and performance for the next generation of CPUs. Analogix’s expertise in DisplayPort to VGA design ensures compatibility with all existing VGA displays.
Main Features:
VGA Output
Supports resolutions up to WQXGA (2560x1600 @60Hz, 24bpp)
VGA output meets VESA VSIS v1r2 clock jitter specification
VGA output pixel rate up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detect
EDID and MCCS pass-through support
DDC speed control for use with longer VGA cables
DisplayPort Input
VESA compliant DisplayPort 1.2 receiver
VESA compliant eDP v1.3 receiver
2 lane high speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Power optimized for Ultra books
Under 350mW operation at WUXGA resolutions
15mW standby power
DisplayPort HBR2 capability allows for single lane operation up to WUXGA. Saves 50mW of DP Tx power
3.3V and 1.05V power requirements easily found on next generation motherboards. No need for external regulators, saving power, space, and cost.
Other Features
Minimum BOM requirements
Default settings changeable with I2C
-10 to +75o C operating temperature
Applications:
Automotive
Notebook/Desktop PC
Package:
7x7mm, 48 QFN (0.5mm pitch) package
Standards Compliance:
DisplayPort 1.2
eDP 1.3
Power Requirements:
3.3V and 1.05V power requirements easily found on next generation motherboards.
ANX1122 is a high-performance low power DisplayPort 1.2 to 24bpp dual-/single-channel LVDS translator. It is designed for connecting motherboards to legacy LVDS LCD panels.
Main Features:
DisplayPort Input Interface
eDP 1.3 compliant
1/2 lane high-speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Resolutions up to WQXGA (2560x1600@60Hz, 24bpp) with pixel clock frequency up to 270 MHz
Industrial temperature version only supports 2.7 and 1.62Gbps DisplayPort connections (resolutions up to WUXGA, 1920x1200)
Standard AUX channel link up to 1Mbps bandwidth
DisplayPort mode spread spectrum clock (SSC) support
Stereo (3D) video output support
LVDS Output Interface
8-BPC LVDS output with single/dual ports
Programmable LVDS swing, channel swap, and polarity invert
LVDS central spectrum spreading with amplitude up to +/-1.75%
Programmable by the DP transmitter through AUX channel, or by local I2C slave
