MIPI-DSI/DPI to USB Type-C™ Bridge (Port Controller with MUX)
Overview:
ANX7625 is a mobile HD transmitter designed for portable devices such as smartphones, tablets, Ultrabooks, docking stations, sports cameras, camcorders, and so on. It enables a mobile device to transfer audio, video, and data simultaneously. The ANX7625 converts MIPI™ to DisplayPort™ 1.3 high-performance video with the resolution up to 4K UHD. The built-in intelligent crosspoint switch provides support for USB Type-C, USB 3.1 data transfer, and the DisplayPort Alternate Mode signaling over USB Type-C. Additionally, its on-chip microcontroller (OCM) provides the capabilities to manage signal switching, Channel Configuration (CC) detection, USB Power Delivery (USB-PD), Vendor Defined Message (VDM) protocol, and other functions defined in the USB Type-C and USB Power Delivery specifications. Overall, the ANX7625 is designed as a single bridge IC between MIPI interface and USB 3.1 interface of the Application Processors to allow for a USB Type-C connector on mobile devices.
The ANX7625 can be adopted by Intel, AMD, Qualcomm, MTK platform designs.
Main Features:
Standard compliance
USB Type-C 1.2, DisplayPort 1.3, MIPI-DSI 1.3, MIPI-DPI 2.0, HDCP 2.2 and 1.4, USB-PD 3.0, VESA® DSC 1.1
Integrated USB Type-C support
USB3.1 Gen1 (5.0 Gbps)
DisplayPort Alternate Mode
Simultaneous USB 3.1 Gen1 (5.0 Gbps) and DisplayPort Alternate Mode
USB-PD 3.0 on CC wire
On-chip microcontroller to implement USB-PD messaging and DisplayPort related functions
DisplayPort transmitter
DisplayPort transmitter (2-lanes @ 6.75 Gbps)
Configurable 1-lane or 2-lane output supports: HBR2.5, HBR2, HBR, and RBR data rates
Video resolution supported: up to 4K (4096x2160p30) or Ultra-HD (3840x2160p30)
AUXP and AUXN support
HDCP2.2 and 1.4 support
Digital audio and video input
MIPI-DSI (4-lanes) at 1.5 Gbps/lane
MIPI-DPI 12-bit double data rate with the maximum pixel clock rates up to 150 Mpixels/sec
DSC with 3:1 or 2:1 compression ratio
I2S: up to 8-channel, 192 kHz digital audio support with TDM format
System operation
Reference input clock: 26 MHz and 27 MHz
Slave I2C device control interface
Built-in video BIST patterns and audio tone generator for system self-test
Power supply
1.0V, 1.8V, and 3.0V
Package options: 64 VFBGA
Applications:
Accessories
Notebook/Desktop PC
Smartphone/Tablet
Package:
64 VFBGA
Standards Compliance:
DisplayPort 1.3 PHY and electrical specifications
MIPI-DSI 1.02
USB Power Delivery Specification v2.0 (rev 1.0)
USB Type-C Cable and Connector Specification (rev 1.1)
The ANX7737 is a DisplayPort (DP) to HDMI (up to Ultra-HD, 4K using HBR2.5) converter, which includes 3D display delivery capability. It is designed to interoperate with any other DisplayPort enabled transmitter, with a maximum resolution of FullHD including 3D display, in smartphones, tablets, Ultrabooks, sports cameras, camcorders, and set top boxes. ANX7737 can support up to HBR2.5 in conjunction with an Analogix 4K transmitter. ANX7737 transforms the DisplayPort output of a source device to HDMI or DVI output so that the device can connect to any high-definition TV, monitor, or projector.
Main Features:
Standard compliance
DisplayPort, HDMI, HDCP
DisplayPort receiver
1-lane DisplayPort1.2 input with link speed of RBR (1.62Gbps), HBR (2.7Gbps), HBR2 (5.4Gbps), and HBR2.5 (6.75Gbps)
Advanced WideEyeTM SerDes technology capable of receiving data over long and low quality cables
Stereo (3D) video support
HDCP content protection
HDMI transmitter
Supports all HDMI 1.4b 4K resolutions, in conjunction with an Analogix 4K transmitter, including 3840x2160@30Hz and 4096x2160@24Hz video formats
Up to 36bpp color depth support at Full-HD
3D video output support for all HDMI 1.4b 3D modes
Remote control support through Consumer Electronics Control (CEC)
HDCP version 1.4 and 2.2 pass-through content protection
System operation
On-chip Microcontroller (OCM)
Slave I2C device control interface
Master I2C device control interface available on
DisplayPort CONFIG signals
Built-in video test pattern generator
Power requirements
1.0V and 1.8V power supplies
Package offered: 64-pin QFN, 8mm x 8mm, 0.4mm pin-pitch
ANX6210 is a DisplayPort to VGA converter designed for motherboards. With its single HRB2 lane, ANX6210 can support WDXGA (2048x1152) as its max resolution. Its on-chip MCU and memory eliminates the needs for any external configuration or setup. It automatically directs the DisplayPort output from the PC or mobile phone to VGA, effectively working with all types of legacy monitors, projectors, and TVs. ANX6210 supports a single 3.3V power supply with an integrated 1V low-dropout (LDO) regulator.
Main Features:
VGA Output
Supports resolutions up to WDXGA (2048x1152@60Hz,24bpp)
VGA output meets VESA VSIS v1r2 clock jitter specification
VGA DAC work range is up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detect
Powered from DisplayPort source
EDID and MCCS pass-through support
DisplayPort Input
DisplayPort 1.2 compliant receiver
VESA® compliant eDP v1.3 receiver
1 lane high-speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Optimized for motherboard design
With 1.0 LDO on, single 3.3V power supply supported
Super low power consumption: 480mW active power (1080p@60Hz, 1V LDO powered on)
ANX9833 is a DisplayPort to VGA adapter IC designed to connect a DisplayPort 1.2/1.1 source to a VGA display. With its on-chip MCU and memory, the ANX9833 does not require any external configuration or setup. It automatically directs DisplayPort output from adapters to VGA, effectively working with all types of legacy monitors, projectors, and TVs. ANX9833 provides Gbps bandwidth over two lanes to reach WUXGA (1920x1200) resolutions.
Main Features:
VGA Output
Resolutions up to WUXGA (1920x1200@60Hz, 24bpp)
VGA output meets VESA VSIS v1r2 clock jitter specification
VGA DAC work range up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detection
Getting power from DisplayPort source
EDID and MCCS pass-through support
DisplayPort Input
VESA® compliant DisplayPort 1.2 receiver
Two-lane high-speed differential input with configurable speed: 2.7Gbps or 1.62Gbps, total bandwidth up to 5.4Gbps
Optimized for VGA Adapters
Integrated MCU and EEPROM for added flexibility
Single 3.3V power supply or 3.3V/1.0V power supply supported
5.0V power output for VGA DDC
Low BOM requirements
System Operation
Field upgradable through DP AUX or I2C
MCU can control external components
-10 to +75o operating temperature
Applications:
Accessories
Notebook/Desktop PC
Package:
6x6mm, 48 QFN (0.4mm pitch)
Standards Compliance:
DisplayPort 1.2
Power Requirements:
600mW active power with all regulators active
Standby power: 12mW with 1V low-dropout (LDO) regulator off
While VGA is losing its popularity in notebooks, there continues to be a need for VGA connections with its huge installed base of monitors, projectors, and TVs. The ANX6212, designed for motherboards, addresses this gap through the high performance DisplayPort to VGA converter of its kind. With its on-chip MCU and memory, the ANX6212 does not require any external configuration or setup. The ANX6212 automatically directs the DisplayPort output from the PC or mobile phone to VGA, effectively working with all types of legacy monitors, projectors, and TVs.
Main Features:
VGA Output
Supports resolutions up to WQXGA (2560x1600@60Hz, 24bpp)
VGA output conforms to VESA® VSIS v1r2 clock jitter specification
VGA output pixel rate up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detect
EDID and MCCS pass-through support
DisplayPort Input
VESA compliant DisplayPort 1.2 receiver
VESA compliant eDP v1.3 receiver
Two-lane high-speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Optimized for VGA Adapters
Integrated MCU and EEPROM for added flexibility
Single 3.3V power supply
5.0V power output for VGA DDC
Minimum BOM requirements
System Operation
Under 350mW operation at WUXGA resolutions (no regulators)
Field upgradable through DP AUX or I2C
MCU can control external components
-10 to +75o C operating temperature
Applications:
Automotive
Notebook/Desktop PC
Package:
6x6mm, 48 QFN (0.4mm pitch)
Standards Compliance:
DisplayPort 1.2
eDP 1.3
Power Requirements:
600mW active power with all regulators active
Standby Power: 12mW with 1V low-dropout (LDO) regulator off
The ANX6211 is a DisplayPort to VGA converter featuring low power consumption, high performance, and cost-effective. Designed for motherboards, the ANX6211 is optimized in terms of space, power, and performance for the next generation of CPUs. Analogix’s expertise in DisplayPort to VGA design ensures compatibility with all existing VGA displays.
Main Features:
VGA Output
Supports resolutions up to WQXGA (2560x1600 @60Hz, 24bpp)
VGA output meets VESA VSIS v1r2 clock jitter specification
VGA output pixel rate up to 270 MHz
Low power standby mode with automatic monitor plug and unplug detect
EDID and MCCS pass-through support
DDC speed control for use with longer VGA cables
DisplayPort Input
VESA compliant DisplayPort 1.2 receiver
VESA compliant eDP v1.3 receiver
2 lane high speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Power optimized for Ultra books
Under 350mW operation at WUXGA resolutions
15mW standby power
DisplayPort HBR2 capability allows for single lane operation up to WUXGA. Saves 50mW of DP Tx power
3.3V and 1.05V power requirements easily found on next generation motherboards. No need for external regulators, saving power, space, and cost.
Other Features
Minimum BOM requirements
Default settings changeable with I2C
-10 to +75o C operating temperature
Applications:
Automotive
Notebook/Desktop PC
Package:
7x7mm, 48 QFN (0.5mm pitch) package
Standards Compliance:
DisplayPort 1.2
eDP 1.3
Power Requirements:
3.3V and 1.05V power requirements easily found on next generation motherboards.
ANX1121 is a low cost high quality DisplayPort to LVDS converter offering up to 18-bits per pixel and single channel LVDS output support. It provides a bridge between DisplayPort-enabled next generation source devices (such as GPUs) and existing LVDS displays. Featuring low power and EMI reduction techniques, combined with its low cost and small form factor, it is ideal for motherboards and other systems with embedded displays.
Main Features:
VESA Compliant DisplayPort™ 1.1a Receiver
Configurable 1 lane operation
1.62/2.7Gbps data rate support
AUX channel link up to 1Mbps bandwidth
All DisplayPort receiver side registers accessible by the AUX channel and I2C slave interface
Spread spectrum clock (SSC) support for improved EMI performance
Single channel LVDS output
Single Channel: Up to 120 MHz pixel clock
Up to 18-bits per pixel
Video Modes
Up to 1680 x 1050@60Hz
18 bits per pixel support
LVDS Spread Spectrum Clocking for reduced EMI
On-chip ring oscillator, no external clock required
Low BOM cost, no local MCU required
Fully controllable via DisplayPort Tx through AUX channel
Low power design supporting several power saving modes
The ANX7738 is a SlimPort to HDMI (up to Ultra-HD, 4K in Turbo mode) converter, which includes 3D display delivery capability.Also, it is designed to interoperate with any other MyDP or DisplayPort™ enabled transmitter,with a maximum resolution of Full-HD including 3D display, in ultrathin notebooks, tablets, smartphones, camcorders, and digital still cameras. ANX7738works in conjunction with MyDP/DisplayPort transmitters, such as the ANX7812, ANX7814, ANX7816, and more. ANX7738 transforms the MyDP/DisplayPort or SlimPort (Turbo mode) output of a source device to HDMI or DVI output so that the device can connect to any high-definition TV, monitor, or projector.
Main Features:
HDMI Transmitter
Connects to any HDMI receiver
Max TMDS link rate up to 300Mpixels/sec
Up to 36bpp color depth support at Full-HD
3D video output support
Remote control support through Consumer Electronics Control (CEC)
HDCP content protection
SlimPort/MyDP/DisplayPort Receiver
SlimPort (Turbo mode) DisplayPort or MyDP input
Configurable 1-lane input supports: Turbo mode, HBR2, HBR, and RBR data rates
Advanced WideEye™ SerDes technology capable of receiving data over long and low quality cables
Spread Spectrum Clocking (SSC) support
Stereo (3D) video input support
Single wire AUXP (C-WIRE) sideband communication
Integrated remote control support
HDCP content protection
System Operation
Integrated On-chip Microcontroller (OCM) for software free operation
Slave I2Cdevice control interface
Built-in video test pattern generator
Applications:
Accessories
Notebook/Desktop PC
Smartphone/Tablet
Package:
64-pin QFN, 8mm x 8mm, 0.4mm pin-pitch
Standards Compliance:
MyDP
RoHS Compliant and Halogen Free
HDMI
HDCP
DisplayPort
Power Requirements:
1.0V and 1.8V
3.3V input requirement eliminated by an integrated boost regulator
Standby power: <20mW, while monitoring cable detection
