10G Active Redriver with Linear Equalization for USB3.2/DisplayPort™
Overview:
ANX7493-AA is a 4-lane redriver capable of switching DisplayPort (DP) and USB3.2 Gen 2x2 10Gbps signals to support a single Type-C™ (USB-C™) port with DisplayPort Alternate Mode. ANX7493-AA can be also configured to a DisplayPort (DP)2.0 Redriver which supports up to 4-lane UHBR10. It is backward compatible with DP 1.4a and USB3.2 Gen 2x2 and Gen 2x1 protocols. Each lane in the ANX7493-AA Redriver has a maximum signal speed of 10Gbps. Two lanes can be bonded to increase the total link bandwidth to 20Gbps. Work modes are set via I2C registers. ANX7493-AA has built-in redriver to recover both the USB and DP signals with loss compensation of 12dB for USB and DP. ANX7493-AA supports a high-gain bandwidth linear amplifier with Continuous Time Linear Equalization (CTLE). ANX7493-AA integrates the AUX snooping for detecting DP states.
Main Features:
Built-in redrivers
Integrated re-driver for USB3.2 up to Gen 2 @ 10Gbps
Integrated re-drivers for DisplayPort up to UHBR10 @ 10Gbps.
Supports both host (source) and device (sink) applications in USB-C subsystems with DisplayPort Alternate Mode
Loss compensation to recover up to 12dB channel loss
Work mode and CTLE configurations
Work mode set by I2C registers
Datapath orientation and direction set by I2C registers or GPIO
CTLE configurations set by I2C registers or GPIO
Serial and debug interfaces
I2C Slave interface, up to 1MHz, for mux and redriver configuration
Industry standard compatibility
USB3.2 specification
DisplayPort 2.0 specification
USB Type-C r2.0 specification
Low-power design
AUX CH commands snooping for power saving in DP mode
USB high speed and LFPS signals detection for power saving in USB mode
Analog power supply at 1.8V
I/O power supply at 1.8V − Integrated Core power supply at 1.2V
Commercial temperature range of 0C to 70C
Applications:
Accessories
Notebook/Desktop PC
Storage/Server
Package:
QFN-50, 4.7mm x 6.4mm, 0.90mm Z-height, 0.35mm pin-pitch
ANX7580 is a low-power mobile HD receiver targeted primarily for single display protocol conversion from DisplayPort to MIPI. With a 4-lane DisplayPort1.4 input and a single MIPI Output with 3:1 DSC support, ANX7580’s feature set is optimized to meet the high performance requirements for current and next generation single and dual clamshell display applications as well as Head-Mounted Displays (HMD) for Augmented Reality (AR) and Virtual Reality. Moreover, with data rate support of up to 6.75Gbps on its DisplayPort input, ANX7580 is an ideal companion device for SlimPort transmitters currently implemented in many leading smart phones. The ANX7580 can also supports eDP on its input making it an ideal converter for x86 based mobile platforms.
Main Features:
Other Features
Standard compliance
DisplayPort1.4, HDCP2.2/1.4
MIPI-DSI 1.2 and D-PHY 1.1
DisplayPort Receiver
DisplayPort1.4 receiver
Configurable 1, 2 or 4-lane input supports: HBR2.5 (6.75Gbps), HBR2 (5.4Gbps), HBR (2.7Gbps), and RBR (1.62Gbps) data rates
Horizontal left / right line splitting
3D stereo modes
HDCP2.2 and HDCP1.4 support
Resolution
DisplayPort Receiver Input Bandwidth supports up to 4K x 2K x 60Hz
ANX7533 is a low-power 4K Ultra-HD (4096x2160p60) mobile HD receiver targeted primarily for Virtual Reality (VR) headsets. With a 4-lane DisplayPort1.4 input and dual MIPI outputs, ANX7533’s feature set is optimized to meet the high performance requirements for current and next generation Head-Mounted Displays (HMD) for Augmented Reality (AR) and Virtual Reality. Moreover, with data rate support of up to 6.75Gbps on its DisplayPort input, ANX7533 is an ideal companion device for SlimPort transmitters currently implemented in many leading smart phones.
Main Features:
Other Features
Standard compliance
DisplayPort1.4, HDCP2.2/1.4
MIPI-DSI 1.2 and D-PHY 1.1
DisplayPort Receiver
DisplayPort1.4 receiver
Configurable 1, 2 or 4-lane input supports: HBR2.5 (6.75Gbps), HBR2 (5.4Gbps), HBR (2.7Gbps), and RBR (1.62Gbps) data rates
Horizontal left / right line splitting
3D stereo modes
HDCP2.2 and HDCP1.4 support
Resolution
DisplayPort Receiver Input Bandwidth supports up to 4K x 2K x 60Hz
ANX7530 is a low-power 4K Ultra-HD (4096x2160p60) mobile HD receiver targeted primarily for Virtual Reality (VR) headsets. With a 4-lane DisplayPort1.4 input and dual MIPI outputs, ANX7530’s feature set is optimized to meet the high performance requirements for current and next generation Head-Mounted Displays (HMD) for Augmented Reality (AR) and Virtual Reality. Moreover, with data rate support of up to 6.75Gbps on its DisplayPort input, ANX7530 is an ideal companion device for SlimPort transmitters currently implemented in many leading smart phones.
Main Features:
Other Features
Standard compliance
DisplayPort1.4, HDCP2.2/1.4
MIPI-DSI 1.2 and D-PHY 1.1
DisplayPort Receiver
DisplayPort1.4 receiver
Configurable 1, 2 or 4-lane input supports: HBR2.5 (6.75Gbps), HBR2 (5.4Gbps), HBR (2.7Gbps), and RBR (1.62Gbps) data rates
Horizontal left / right line splitting
3D stereo modes
HDCP2.2 and HDCP1.4 support
Resolution
DisplayPort Receiver Input Bandwidth supports up to 4K x 2K x 60Hz
The ANX7737 is a DisplayPort (DP) to HDMI (up to Ultra-HD, 4K using HBR2.5) converter, which includes 3D display delivery capability. It is designed to interoperate with any other DisplayPort enabled transmitter, with a maximum resolution of FullHD including 3D display, in smartphones, tablets, Ultrabooks, sports cameras, camcorders, and set top boxes. ANX7737 can support up to HBR2.5 in conjunction with an Analogix 4K transmitter. ANX7737 transforms the DisplayPort output of a source device to HDMI or DVI output so that the device can connect to any high-definition TV, monitor, or projector.
Main Features:
Standard compliance
DisplayPort, HDMI, HDCP
DisplayPort receiver
1-lane DisplayPort1.2 input with link speed of RBR (1.62Gbps), HBR (2.7Gbps), HBR2 (5.4Gbps), and HBR2.5 (6.75Gbps)
Advanced WideEyeTM SerDes technology capable of receiving data over long and low quality cables
Stereo (3D) video support
HDCP content protection
HDMI transmitter
Supports all HDMI 1.4b 4K resolutions, in conjunction with an Analogix 4K transmitter, including 3840x2160@30Hz and 4096x2160@24Hz video formats
Up to 36bpp color depth support at Full-HD
3D video output support for all HDMI 1.4b 3D modes
Remote control support through Consumer Electronics Control (CEC)
HDCP version 1.4 and 2.2 pass-through content protection
System operation
On-chip Microcontroller (OCM)
Slave I2C device control interface
Master I2C device control interface available on
DisplayPort CONFIG signals
Built-in video test pattern generator
Power requirements
1.0V and 1.8V power supplies
Package offered: 64-pin QFN, 8mm x 8mm, 0.4mm pin-pitch
The ANX7750 is a SlimPort to DisplayPort lane converter. It takes a 1-lane SlimPort (@HBR2.5 rate) input and converts it to 4-lane DisplayPort (@HBR rate) output. ANX7750 works in conjunction with SlimPort transmitters, such as ANX7805, ANX7808, ANX7812, ANX7814, ANX7816, ANX7836, and more. ANX7750 is particularly suited for seamless plug-and-play to legacy DisplayPort (@HBR rate) HDTV, monitors, and projectors.
Main Features:
Standard compliance
DisplayPort, MyDP, HDCP
SlimPort/MyDP/DisplayPort receiver
1-lane high-speed differential input with configurable speed: HBR2.5, HBR2, HBR, or RBR
Video up to 4K@30Hz resolution
Spread Spectrum Clocking (SSC) support
Stereo (3D) video input support Single wire AUXP (C-WIRE) sideband communication
HDCP content protection
DisplayPort transmitter
1-, 2-, or 4-lane high-speed differential output with configurable speed: HBR or RBR
Stereo (3D) video input support
HDCP content protection
System operation
Integrated On-chip Microcontroller (OCM) for software free operation
ANX1122 is a high-performance low power DisplayPort 1.2 to 24bpp dual-/single-channel LVDS translator. It is designed for connecting motherboards to legacy LVDS LCD panels.
Main Features:
DisplayPort Input Interface
eDP 1.3 compliant
1/2 lane high-speed differential input with configurable speed: 5.4Gbps, 2.7Gbps, or 1.62Gbps
Resolutions up to WQXGA (2560x1600@60Hz, 24bpp) with pixel clock frequency up to 270 MHz
Industrial temperature version only supports 2.7 and 1.62Gbps DisplayPort connections (resolutions up to WUXGA, 1920x1200)
Standard AUX channel link up to 1Mbps bandwidth
DisplayPort mode spread spectrum clock (SSC) support
Stereo (3D) video output support
LVDS Output Interface
8-BPC LVDS output with single/dual ports
Programmable LVDS swing, channel swap, and polarity invert
LVDS central spectrum spreading with amplitude up to +/-1.75%
Programmable by the DP transmitter through AUX channel, or by local I2C slave
The ANX7738 is a SlimPort to HDMI (up to Ultra-HD, 4K in Turbo mode) converter, which includes 3D display delivery capability.Also, it is designed to interoperate with any other MyDP or DisplayPort™ enabled transmitter,with a maximum resolution of Full-HD including 3D display, in ultrathin notebooks, tablets, smartphones, camcorders, and digital still cameras. ANX7738works in conjunction with MyDP/DisplayPort transmitters, such as the ANX7812, ANX7814, ANX7816, and more. ANX7738 transforms the MyDP/DisplayPort or SlimPort (Turbo mode) output of a source device to HDMI or DVI output so that the device can connect to any high-definition TV, monitor, or projector.
Main Features:
HDMI Transmitter
Connects to any HDMI receiver
Max TMDS link rate up to 300Mpixels/sec
Up to 36bpp color depth support at Full-HD
3D video output support
Remote control support through Consumer Electronics Control (CEC)
HDCP content protection
SlimPort/MyDP/DisplayPort Receiver
SlimPort (Turbo mode) DisplayPort or MyDP input
Configurable 1-lane input supports: Turbo mode, HBR2, HBR, and RBR data rates
Advanced WideEye™ SerDes technology capable of receiving data over long and low quality cables
Spread Spectrum Clocking (SSC) support
Stereo (3D) video input support
Single wire AUXP (C-WIRE) sideband communication
Integrated remote control support
HDCP content protection
System Operation
Integrated On-chip Microcontroller (OCM) for software free operation
Slave I2Cdevice control interface
Built-in video test pattern generator
Applications:
Accessories
Notebook/Desktop PC
Smartphone/Tablet
Package:
64-pin QFN, 8mm x 8mm, 0.4mm pin-pitch
Standards Compliance:
MyDP
RoHS Compliant and Halogen Free
HDMI
HDCP
DisplayPort
Power Requirements:
1.0V and 1.8V
3.3V input requirement eliminated by an integrated boost regulator
Standby power: <20mW, while monitoring cable detection
