RD1011 is a bidirectional active USB Type-CTM (USB-C) cable, which includes two paddle cards, each with an ANX7451 device on it. The ANX7451 is a 4x4 re-timing mux capable of switching DisplayPort (DP) and USB3.2 Gen 2 10Gbps signals to support a single USB Type-CTM (USB-CTM) port. The RD1011 design can recover both the USB and DP signals with loss compensation of up to 23dB and 27dB respectively. The RD1011 includes two ANX7410 devices, which act as an on-board programmable MCU and eMarker chip. With ANX7410, ANX7451 can be initiated with optimal settings that enable the RD1011 design to cover 4-meter at 28AWG cable length. RD1011 can be used with any USB-C port on any of the display monitors, docking stations and VR HMDs.
Main Features:
Other Features
Bidirectional active USB-C cable carrying 4L DP or 2L DP and USB3.2
Supports up to 4L of DisplayPort in/out, with signal conditioning up to 8.1Gbps (supports HBR3, HBR2, HBR, RBR rates)
Supports USB3.1 in/out, with signal conditioning up to 10Gbps
Supports USB2.0 (480Mbps)
Compensates signal loss of up to 27dB
Supports plug flip
Powered by VCONN and VBUS
On-board programmable MCU, ANX7410, to initiate ANX7451 with specific settings
ANX7410 acts as an eMarker chip to snoop or respond SOP’ and SOP’’ messages from a USB-C DFP, as per active USB-C cable spec
Two paddle cards (2x re-timers) design to guarantee data throughput performance, and for ease of production
USB Type-C™ Power Delivery v3.0 Controller with De-Mux (USB/DP)
Overview:
ANX7327 is a USB-PD v3.0 port controller with an integrated de-mux that supports switching at data rates of up to 10Gbps. ANX7327 supports high-speed interfaces, such as USB 3.1 (Gen 1 – 5Gbps, Gen 2 – 10Gbps) and DisplayPort™ (DP) 1.4 at up to HBR3 (8.1Gbps). ANX7327 is designed to be placed behind a USB Type-C (USB-C™) receptacle of a USB-C accessory or HDTV or monitor USB-C port. The USB-C port with the embedded IC device behind it enables a passive USB-C cable connectivity between any USB-C source and the accessory or HDTV or monitor to further the USB-C functions to a display or data connectivity downstream. On the source side, when paired with a re-timer mux such as the ANX7440, the ANX7327/7440 combo solution can enable a USB-C full function port with CPUs that have integrated USB-C mux. An On-chip Microcontroller (OCM) is available to manage the signal switching, Channel Configuration (CC) detection, USB Power Delivery (USB-PD) charging and Vendor Defined Message (VDM) protocol, and other functions, as defined in the USB Type-C v1.2 and USB Power Delivery v3.0 specifications. ANX7327 can be configured for an Upstream Facing Port (UFP) to support a USB-C receptacle. When paired with a DP-to-HDMI/VGA bridge (such as the ANX7737/9837), the ANX7327 creates an ideal solution for USB Type-C dongle, docking, HDTV, and monitor applications.
Main Features:
Other key features
High-speed de-mux (4x6) switching up to 10Gbps
4-lanes DisplayPort outputs with link speed of 1.62Gbps, 2.7Gbps, 5.4Gbps, 6.75Gbps, and 8.1Gbps
USB 3.1 signal output (SSTX and SSRX) with Gen1 (5Gbps) and Gen2 (10Gbps) link speed
USB 1.1 Billboard support
DisplayPort Alternate Mode (SlimPort®) communication support through USB-PD structured VDM messaging
Native TCPC-compliant hardware register interface
Integrated VCONN FETs
Built-in 10-bit ADC to monitor VBUS voltage and current
Dedicated control signals for VBUS Source FET, VBUS sink FET, and VBUS auto discharge circuity
Serial and debug interfaces
Slave interface
Industry standard compatibility
USB Type-C r1.2 specification
USB Power Delivery v3.0 r1.0 specification
DisplayPort 1.4 specification
DisplayPort Alternate Mode over USB Type-C r1.1 specification
Universal Serial Bus (USB) Type-C Port Controller Interface r1.0 specification
Low-power design
Single supply at 3.3V
Dedicated supply power pin for flexible I/O power – 1.8V or 3.3V
Ultra-low power consumption (typical 80uW) in standby mode
On-chip Microcontroller (OCM) to implement signal switching, USB-PD messaging, and DisplayPort related functions
ANX7496 is a DisplayPort 4-lane re-timer capable of conditioning DP signals up to 8.1Gbps (supports HBR3, HBR2, HBR, RBR rates). ANX7496 can compensate signal loss of up to 27dB and can operate in either DP transparent mode or Link-Trainable Tunable PHY Repeater (LTTPR) mode. ANX7496 integrates the DP AUX signal pass-through and is protocol aware for better link power management and power savings. ANX7496 can be in various types of applications such as PCs, mobile, accessories, monitors, and VR HMDs with various connectors such as mini-DP, standard-DP, or even USB Type-C™ (USB-C™).
Main Features:
Other key features
Built-in re-timers
Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps
Supports both transparent mode and non-transparent mode (transparent or LTTPR)
Loss compensation to recover up to 27dB channel loss
Integrated AUX pass-through
Integrated AUX detection for link training and protocol awareness for better link power management (LPM)
Reference clock for re-timer
Utilizes a 24MHz reference XTAL or 1.05V single-ended clock source
Serial and debug interfaces
I2C Slave interface, up to 1MHz, for re-timer configuration
Industry standard compatibility
DisplayPort 1.4 specification Low-power design
Low-power design
Analog power supply at 1.8V
Dedicated supply power pin for I/O power at 1.8V Packages
Commercial temperature range of 0C to 70C
Applications:
配件
笔记本/桌面PC
VR/AR头戴设备
Notebooks, desktops, and 2-in-1s
Package:
BGA-56, 4.0mm x 4.5mm, 0.5mm ball-pitch
QFN-60, 7.0mm x 7.0mm, 0.85mm Z-height, 0.4mm pin-pitch
.png)
